Product ID:HIT MELT ADHESIVE, 9224
MSDS Date:07/12/1990
FSC:8040
NIIN:00N042792
MSDS Number: BSYQT

WORTHEN INDUSTRIES

3 EAST SPIT BROOK RD
NASHUA, NH 03060
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 603-888-5443

Cage: 56612

WORTHEN INDUSTRIES

NASHUA, NH 03060 US

Telephone: 603-888-5443

Cage: 56612

PARAFFIN WAX

CAS: 64742-43-4

OSHA PEL N/K

ACGIH TLV: N/K

PARAFFIN; (SYNTHETIC WAX)

CAS: 8002-74-2

RTECS: RV0350000

OSHA PEL 2 MG/M3 (FUME)

ACGIH TLV: 2 MG/M3 (FUME)

BENZENEPROPANOIC ACID,

CAS: 6683-19-8

RTECS: DA8304900

OSHA PEL N/K

ACGIH TLV: N/K

HYDROXYPHENYL-1-OXYPROPOXY)METHYL)-1,3-PROPANEDIYL

RTECS: 9999999ZZ

EVA COPOLYMER

CAS: 24937-78-8

OSHA PEL N/K

ACGIH TLV: N/K

THERMOPLASTIC HYDROCARBON RESIN

CAS: 9011-11-4

OSHA PEL N/K

ACGIH TLV: N/K

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE/CHRONIC: INHAL IS NOT POSS IF
MATL IS IN SOLID FORM. IF MOLTEN, OVEREXP WILL CAUSE HDCH. EYES:
SOLID MATL HAS NO EFT. MOLTEN MATL CAN IRRITATE & BURN IF IN DIRECT
CONT. SKIN: SOLID MATL HAS NO E FT. MOLTEN MATL WILL BURN UNTIL
POLYMERIS COOL. INGEST: SOLID MATL HAS NO EFT. MOLTEN MATL WILL
BURN (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: INTENSELY. IF PERSONAL CONT W/ MOLTEN
MATL PRDCES A BURN SEE A PHYS/BURN CTR IMMED. INHAL: INHAL OF
MOLTEN MATL FUMES MAY RSLT IN HDCH IF INSUFFICIENT VENT. SKIN/EYE
CONT: MOLTEN MATL WILL C AUSE SEV EYE DAM IF CONT OCCURS. FUMES
FROM MOLTEN MATL MAY CAUSE SOME IRRIT IF ADEQ VENT IS NOT USED.
(SUPP DATA)
Medical Cond Aggravated by Exposure:HEADACHES.

First Aid:INHAL: REMOVE TO FRESH AIR. EYES: IF MOLTEN, RINSE W/COLD
WATER IMMED FOR AT LST 15 MIN & SEE A PHYS IMMED. SKIN: IMMED
SUBMERGE BURNED SKIN AREA IN COLD CLEAN WATER. DO NOT ATTEMPT TO
PULL AWAY SOLID IFIED MATL ADHERING TO SKIN. SEEK MED ATTN. INGEST:
BRING TO HOSP IMMED. MATL @ ROOM TEMP IS A SOLID MATL BUT IS
NORMALLY USED AS A HOT MELT, SO TREAT ANY PERSONAL CONT W/MOLTEN
MATL AS (SUPP DATA)

Flash Point:<400F,<204C
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:COOLING WITH WATER WILL SOLIDIFY THE
MATERIAL VERY RAPIDLY. NO UNUSUAL FIRE AND EXPLOSION HAZARDS ARE
KNOWN.

Spill Release Procedures:NORMAL HOUSEKEEPING FOR SOLID MATERIAL. CLEAN
MACHINERY OF RESOLIDIFIED MATERIAL W/SOLVENT, TAKING CARE TO
ELIMINATE ALL HEAT AND SPARK SOURCES. FOR LARGE SPILLS OF MOLTEN
LIQUID, ALLOW TO SOLIDIFY AN D SCRAPE UP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:NOT APPLICABLE IN SOLID FORM. REVIEW
EMERGENCY AND FIRST AID PROCEDURES BEFORE HANDLING MOLTEN
MATERIALS.
Other Precautions:NONE IN SOLID FORM.

Respiratory Protection:NOT REQUIRED FOR NORMAL USAGE CONDITIONS WITH
ADEQUATE VENTILATION. USE NIOSH/MSHA APPROVED RESPIRATOR
APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:LOCAL EXHAUST IF USED IN A CONFINED AREA. MECHANICAL
VENTILATION REQUIRED FOR LARGE VOLUME USE.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM SAFETY GOGGLES .
Other Protective Equipment:FULL BODY COVERING CLOTHES IF SPLASHING OR
SPRAYING MOLTEN MATERIAL.
Work Hygienic Practices:ALWAYS HANDLE CHEMIALS WITH CARE. BE SURE TO
HAVE EYE RINSE AND SHOWER STATION WITHIN THE WORKING AREA.
Supplemental Safety and Health
EFTS OF OVEREXP: SKIN ABSORP: MOLTEN MATL WILL CAUSE INTENSE SKIN BURNS
AS WOULD ANY OTHER MOLTEN THERMOPLATIC MATL. INGEST: SHOULD INGEST
OCCUR, MOLTEN POLYMER WILL BURN INTERNAL ORGANS SEVERELY. SOL ID
MATERIAL IF INGESTED WILL CAUSE NO DAMAGE AT ALL. FIRST AID PROC: A
NORMAL BURN.

HCC:N1
Vapor Density:HVR/AIR
Spec Gravity:0.8(H2O=1)
Evaporation Rate & Reference:Solubility in Water:NONE
Appearance and Odor:CLEAR TO AMBER SLATS OR PELLETS.

Stability Indicator/Materials to Avoid:YES
NONE.
Stability Condition to Avoid:NONE.
Hazardous Decomposition Products:ON THERMAL DECOMPOSITION IT MAY EMIT
TOXIC FUMES, INCLUDING CARBON MONOXIDE &/OR CARBON DIOXIDE.

Waste Disposal Methods:NORMAL DISPOSAL FOR SOLID WASTE AS MIGHT BE USED
FOR OTHER PLASTIC MATERIALS SUCH AS POLYETHYLENE. DISPOSE OF I/A/W
ALL LOCAL, STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.